Top-load washer suspension rod replacement
If your top loader bounces like a basketball on spin, the four rods that hang the tub are probably worn. A kit swaps in about an hour.
- Difficulty
- Moderate
- Time
- 45 min–2 hr
- Typical part cost
- $25–$80Pro: $100–$350
- Tools
- 4See the list
Lift the top, then unhook each rod and hook in a new one. Lifting the tub a little to free each rod takes some strength.
What it does
What the suspension rods does
In many top loaders, the tub does not sit on anything. It hangs from four rods hooked to the top corners of the cabinet, with a spring and a damper cup at the bottom of each.
The damper cups add friction, so the tub settles quickly instead of bouncing when it spins up.
Why it fails
The damper cups wear smooth and stop adding friction. The tub sags or bounces and hits the cabinet.
A spring or a rod end can break, and the tub drops on one side.
Heavy, unbalanced loads speed up the wear.
Symptoms
Signs of a bad suspension rods
Bangs the cabinet on spin
Loud thumps as the spin speeds up, often worse with towels or bedding.
Full diagnosisWalks or bounces
The whole washer rocks or moves across the floor on spin.
Full diagnosisTub sits crooked
With the lid open, the gap between the tub and the cabinet is wider on one side.
Unbalance code or pauses
Some washers stop and show an unbalance code even with a balanced load.
How to test it
Test the suspension rods before you buy
- Level the washer side to side and front to back, and make sure all four legs sit firmly.
- Run a rinse and spin with no clothes in it.
- Good
- Smooth empty spin. Spread heavy loads out evenly next time.
- Bad
- Still banging empty and level. Check the rods.
- Unplug the washer and open the lid.
- Push down firmly on the rim of the tub and let go. Then push it side to side.
- Good
- The tub drops a little and comes back up, settling quickly.
- Bad
- It bounces several times, drops a lot, or sits lower on one side. The rods are worn.
Safety first
Before you touch anything
- 1
Unplug the washer
Pull the plug before you open the top.
- 2
Empty tub only
Do this with the tub empty. Water makes the tub far too heavy to lift on the rods.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Putty knifeStiff, 1-1/2 in.Releases the spring clips that hold many top-load cabinet tops.Typically $5–$12Shop this tool
- Multi-bit screwdriverPhillips, flat, squareRemoves the console screws on models that open from the back.Typically $10–$25Shop this tool
- Work glovesThe cabinet corners and rod hooks are sharp.Typically $8–$20Shop this tool
- HeadlampThe rod ends sit down beside the tub.Typically $12–$30Shop this tool
Step by step
How to replace the suspension rods
- 1
Unplug it and empty the tub
Pull the plug, close both valves, and make sure no water is left in the tub.
- 2
Lift the top
Top loaders open in different ways. On many, take out the screws at the back of the top, or release the front clips with a putty knife, then slide the top forward and lift it off its rear brackets. Tape the lid shut and lean the top against the wall. Unplug the lid switch if the harness is too short.
- 3
Unhook one rod
Lift the top end of the rod out of its cup at the cabinet corner. On many rods you turn it a quarter turn to free it, then lower it down beside the tub.
Work the rod out through the tub bracket from below. On many models you need to tilt the washer back, or lay it on its side, to reach it. Get a helper for that, because a tipping washer can hurt you.
- 4
Hook in the new rod
Feed the new rod up through the tub bracket along the same path, with its spring and damper at the bottom. Stand the washer back up, lift the tub a little, and hook the top end into its cup.
Repeat at each corner, one rod at a time. Do not mix bushings or cups from different kits.
Careful. Use a kit matched to your model. Mixing rod lengths or bushings can leave the tub crooked.
Buy the part
Suspension rods
Opens Amazon in a new tab. Where’s my model number?
What to look for
- A four-rod kit listed for your washer's model number.
- Rods, springs and damper cups all included.
- 5
Check the tub sits level
Rock the tub side to side. It should feel firmer than before and hang evenly, with the same gap all the way around.
- 6
Close up and test
Lower the top until it clips in. Plug in and run a rinse and spin with a towel load.
Buy the part
Get the right replacement
Buy the part
Suspension rods
Opens Amazon in a new tab. Where’s my model number?
What to look for
- A four-rod kit listed for your washer's model number.
- Rods, springs and damper cups all included.
Know your limits
When to call a pro
Stop and call a pro if
- New rods and a level washer still bang. The tub, the balance ring or the drive may need a pro's look.
- You hear grinding or a roar on spin, which can point to the bearings or the transmission.
- The tub has to come out to reach the rods on your model.
FAQ
Suspension rods questions
Do I need to replace all four rods?
Yes. Rods wear together. One new rod with three worn ones leaves the tub uneven.
My washer only bangs with towels. Is that the rods?
Wet towels are heavy and bunch up, so some thumping can be the load. If it bangs on an empty rinse and spin too, the rods are the likely cause.
Is this the same as front-load shock absorbers?
Same job, different part. Front loaders use shock absorbers under the tub.
Related
Keep going
- SymptomWasher shaking, banging or walkingThe washer bangs, shakes or walks during spin. Rebalance the load and level the washer first. If it still bangs, the suspension rods or shock absorbers are worn.Open guide
- Washer partShock absorbersShock absorbers connect a front loader's tub to the base and soak up its movement on spin. When they wear out, the tub bangs and the washer walks. Level the washer first, then replace them as a set.Open guide
- Washer partLid switch or lid lockThe lid switch tells a top loader its lid is shut, and on many newer washers it also locks the lid. When it fails the washer will not spin or start. Test it and swap it in under an hour.Open guide
- Washer partAgitator and agitator dogsOn two-piece agitators, small cogs called agitator dogs drive the top half. Worn dogs, or a stripped agitator coupler, leave clothes floating instead of turning over. Both are quick fixes from inside the tub.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
