Top-load washer lid switch replacement
A top loader that fills but will not spin, or will not start at all with the lid shut, often has a worn lid switch or lid lock. It is a small part and usually not an expensive one.
- Difficulty
- Easy
- Time
- 20–45 min
- Typical part cost
- $10–$60Pro: $85–$300
- Tools
- 3See the list
Lift the top or the console, unplug one connector, take out a screw or two. Getting the top open is the trickiest part.
What it does
What the lid switch does
The lid switch sits under the cabinet top, next to the lid opening. A tab or strike on the lid presses it when you close the lid.
Top loaders only spin, and on many models only drain, with the lid shut. On many newer washers the switch is part of a lid lock that also latches the lid before agitating or spinning.
On some washers the switch only sits in the spin circuit. Those fill and agitate normally and then skip the spin.
Why it fails
The switch contacts wear out after years of opening and closing, and stop closing reliably.
The plastic strike on the lid snaps off, so nothing presses the switch even though the switch is fine.
On lid locks, the small lock motor or solenoid can fail, so the lid never locks and the washer will not go on.
Symptoms
Signs of a bad lid switch
Fills, then will not spin
The washer fills and maybe agitates, but never spins. Clothes come out soaking.
Full diagnosisWill not start with the lid shut
Nothing happens, or the lid lock light blinks, even though the lid is down.
Full diagnosisLid lock light flashes
On washers with a lid lock, a flashing lock light or a lid error code means it could not lock or confirm the lid.
Strike broken off
Look under the edge of the lid. If the little tab that presses the switch is gone, that is your problem.
How to test it
Test the lid switch before you buy
- Lift the lid and find the tab or strike on its underside, near the front.
- Look for cracks, bends or a missing piece. Check that it lines up with the slot in the cabinet.
- Good
- A whole, straight strike that lines up means the switch is the next suspect.
- Bad
- A broken or bent strike. Replace the strike or the lid part that carries it first.
- Unplug the washer and lift the top or the console to reach the switch (steps 1 to 3 below).
- Unplug the switch's connector.
- Put one probe on each of the switch terminals. Press the switch the way the lid strike would, then release it.
A good switch typically reads
Near 0 Ω (beeps) when pressed, OL when released
Typical range. Check your part label or manual for the exact spec. Lid locks have extra wires for the lock motor. Use the wiring diagram on your washer to find the switch pair.
- Good
- Continuity that comes on when pressed and goes off when released means the switch works.
- Bad
- No change when you press it means the switch has failed. Replace it.
Safety first
Before you touch anything
- 1
Unplug the washer
Pull the plug before you lift the top. The lid switch wires can carry household voltage.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Putty knifeStiff, 1-1/2 in.Releases the spring clips that hold many top-load cabinet tops.Typically $5–$12Shop this tool
- Multi-bit screwdriverPhillips, flat, squareRemoves the console screws and the switch screws.Typically $10–$25Shop this tool
- Nut driver1/4 in. hexOptionalSome consoles and switch brackets use 1/4 in. hex screws.Typically $6–$15Shop this tool
- Digital multimeterΩ, V, µF, µAConfirms the switch is open before you buy a new one.Typically $25–$60Shop this tool
Step by step
How to replace the lid switch
- 1
Unplug the washer
Pull the power plug. Pull the washer out from the wall a little if you need room behind it.
- 2
Open the console or the top
Top loaders open in different ways. On many, you take out a couple of screws at the back of the top, then release a clip or latch tab near each front corner by sliding a putty knife into the seam. Then tilt or lift the top.
On others, the console comes off first, or the top unhooks from brackets at the back. Do not force a thick tool into the seam, because it bends the metal. Your manual or a parts diagram shows which.
- 3
Unplug the switch
Find the switch beside the lid opening. Photograph the wires, then squeeze the tab on the connector and pull it off.
- 4
Remove the old switch
Take out the screw or screws that hold it. Some snap into the cabinet and pop out when you squeeze their tabs.
Note how the wire harness is routed and clipped, so the new one goes back the same way.
- 5
Fit the new switch
Set the new switch in the same spot and fasten it. Route the harness along the same clips, clear of the tub and any sharp edges.
Plug the connector in until it clicks.
Buy the part
Lid switch or lid lock
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The part listed for your washer's model number. A simple switch and a lid lock assembly are not interchangeable.
- The same connector and mounting.
- 6
Close up and test
Lower the top until the clips snap home, or refit the console screws.
Plug in and run a rinse and spin. With the lid shut, it should lock if it has a lock, then spin.
Buy the part
Get the right replacement
Buy the part
Lid switch or lid lock
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The part listed for your washer's model number. A simple switch and a lid lock assembly are not interchangeable.
- The same connector and mounting.
Know your limits
When to call a pro
Stop and call a pro if
- A new switch does not fix it and the strike is fine. The wiring or the control board may be the cause.
- The washer agitates but will not spin even with a good switch. The drive or transmission may need a pro.
- You find burned or melted wires at the switch.
FAQ
Lid switch or lid lock questions
Can I bypass the lid switch?
No. The switch stops the basket while your hands can reach it. A spinning basket can cause serious injury. Replace the switch instead.
My washer agitates but will not spin. Is it the lid switch?
It is the first thing to check. If the switch tests good and the water drains, see washer won't spin for the next suspects, like the motor coupler.
Does a front loader have a lid switch?
No. A front loader uses a door lock that does the same job for its door.
Related
Keep going
- SymptomWasher won't spinThe clothes come out soaking, or the washer agitates but never spins. Check drainage, the lid switch or door lock, and the load first, then the belt or motor coupler.Open guide
- SymptomWasher won't startNothing happens when you press Start, or it lights up but will not begin. Power, the child lock or delay start, and the lid switch or door lock cause most of it.Open guide
- Washer partMotor couplerOn direct-drive top loaders, the motor coupler links the motor to the transmission and breaks on purpose to protect the motor. When it fails, the washer fills and drains but will not agitate or spin.Open guide
- Washer partDrain pumpThe drain pump pushes the water out at the end of each wash and rinse. Clean the filter first. If it still will not drain, test the pump and swap it.Open guide
- Washer partControl boardThe control board runs every step of the cycle and powers the pump, valve, lock and motor. It is the last part to suspect. When it is the cause, swap it plug by plug.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
