WhatsBusted
3D model of a reset button
Also called garbage disposal reset, overload protector

How to reset a garbage disposal

Dead silent when you flip the switch? Look under the sink for a small red button on the bottom. Pressing it brings a lot of disposals back.

Difficulty
Anyone can do it
Time
2–15 min
Typical part cost
$0Pro: $70–$130

Find the button and press it. That is the whole job.

What it does

What the reset does

The red button on the bottom of the disposal, or on the side of some models, is part of a thermal overload protector. Some newer models reset on their own and have no button.

When the motor gets too hot, usually from a jam or a long grind, it trips and the button drops out about a quarter inch. The motor will not run until you press it back in.

Why it fails

It is doing its job when it trips. A jam, or a big load of tough or dense food, makes the motor work too hard.

If it trips again and again on normal use, the motor may be wearing out.

Symptoms

Signs of a bad reset

  • No sound at all

    Nothing happens when you flip the switch. No hum, no spin.

    Full diagnosis
  • Button sticking out

    Feel or look under the unit. A tripped button sits lower than its housing.

  • Stopped after a hum

    It hummed, then went silent. It jammed and then tripped.

    Full diagnosis

How to test it

Test the reset before you buy

Check the buttonNo meter needed
  1. Turn off the wall switch, then unplug the disposal or switch off its breaker.
  2. Look at the bottom of the disposal with a light. Find the small red button. If it has dropped out, it has tripped.
Good
Tripped. Free any jam, let it cool, then press it in (steps below).
Bad
Not tripped, or it clicks in and the disposal is still silent. Check the outlet, the plug and the breaker.

Safety first

Before you touch anything

  1. 1

    Switch off first

    Turn off the wall switch, then unplug the disposal or switch off its breaker, so it cannot start while your hands are under it.

  2. 2

    Let it cool

    Wait a few minutes after it trips. If the button will not stay in, wait about ten minutes and try again.

    Wait about 10 min

Tools you'll need

Grab these first

Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works

See the full repair tool kit

Step by step

How to replace the reset

  1. 1

    Switch it off

    Turn off the wall switch. Unplug the disposal, or switch off its breaker if it is hardwired.

  2. 2

    Free a jam if it hummed

    If it hummed before it went silent, turn the flywheel with a hex key until it moves freely. See how to unjam a disposal.

  3. 3

    Wait, then press

    Give the motor a few minutes to cool. Press the red button gently until it clicks and stays in.

    If it pops back out, wait about ten minutes and try again. Never hit it with a tool.

  4. Buy the part

    Reset button

    Opens Amazon in a new tab. Where’s my model number?

    What to look for

    • Nothing to buy for a reset. A spare 1/4 in. hex key is handy for the jams that cause most trips.
  5. 4

    Power on and test

    Plug it back in or switch the breaker on. Turn on cold water first, then switch it on.

Buy the part

Get the right replacement

Buy the part

Reset button

Opens Amazon in a new tab. Where’s my model number?

What to look for

  • Nothing to buy for a reset. A spare 1/4 in. hex key is handy for the jams that cause most trips.

Know your limits

When to call a pro

Stop and call a pro if

  • You smell burning or see smoke.
  • It trips again and again with normal use.
  • The button is in, the outlet works, and it is still silent.
  • The breaker trips again as soon as you reset it.

FAQ

Reset button questions

Where is the reset button on a garbage disposal?

On the bottom of the unit, facing the floor, on most models. A few have it low on the side. It is usually red. Some newer models have no button and reset themselves after cooling.

Why does my disposal keep tripping?

Usually jams or heavy loads. Run cold water while it grinds and feed food in slowly. If it trips with light use, the motor may be failing.

The reset will not stay in. What now?

The motor is still too hot. Wait about ten minutes and try again.

Related

Keep going

Get the next fix before it breaks

A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.

We send it with Kit. Privacy