Oven broil element test and replacement
Electric ranges only. If broil does nothing, check the element across the oven's ceiling.
- Difficulty
- Easy
- Time
- 15–45 min
- Typical part cost
- $20–$60Pro: $150–$400
- Tools
- 4See the list
Two screws and two wires, overhead. The element's support brackets on the ceiling sometimes need a clip or screw removed too.
What it does
What the broil element does
The broil element runs across the oven's ceiling. On broil it glows red hot to brown food from above.
Gas ranges use a broil burner, or broil under the bake burner in a drawer, instead.
Why it fails
Like the bake element, its coil burns through with age. A blister, a split, a burn mark or a bright spark just before it failed are the usual tells.
Symptoms
Signs of a bad broil element
Broil does nothing
Set to broil, the top element stays dark.
Full diagnosisBlister, split or burn mark
Visible damage on the element along the oven's ceiling.
How to test it
Test the broil element before you buy
- Set the oven to broil and look at the top element after a minute or two.
- Good
- The whole loop glows evenly red.
- Bad
- It stays dark or only part of it glows. Turn the oven off, unplug the range and test it with a meter.
- Unplug the range, let it cool, pull the element down far enough to reach its terminals and pull the wires off.
- Probe the two terminals. Then probe each terminal to the element's metal sheath.
A good broil element typically reads
About 10–50 Ω across the terminals; open to the sheath
Typical range. Check your part label or manual for the exact spec. A dual broil element has three terminals. Test each section from the shared terminal.
- Good
- A steady reading across the terminals and no continuity to the sheath.
- Bad
- OL across the terminals, or any continuity to the sheath. Replace it.
Safety first
Before you touch anything
- 1
Unplug it or switch off both breakers
An electric range runs on 240 V. Unplug it or turn off its breaker, and confirm with a voltage tester before you touch the wires.
- 2
Let the oven cool
The element stays hot long after the oven is off. Let it cool completely.
Wait about 30 min
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Nut driver1/4 in. hexThe mounting screws are usually 1/4 in. hex heads.Typically $6–$15Shop this tool
- Multi-bit screwdriverPhillips, flat, squareFor Phillips screws and terminal screws.Typically $10–$25Shop this tool
- Digital multimeterΩ, V, µF, µAConfirms the element is open before you buy one.Typically $25–$60Shop this tool
- HeadlampYou are working on the oven's ceiling.Typically $12–$30Shop this tool
Step by step
How to replace the broil element
- 1
Power off
Unplug the range, or turn off its breaker.
- 2
Release the element
Take out the racks. Remove the two screws at the back wall where the element's terminals pass through.
If the element is held up by clips or brackets along the ceiling, release those, supporting the element as you go.
- 3
Pull it forward and disconnect it
Ease the element forward so the terminals come through the wall, and pull the wires off. Keep the wires from slipping back through.
- 4
Match the new element
Check the shape, the length, the brackets and the number of terminals against the old one.
Buy the part
Broil element
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your range's model number. Shapes and lengths vary.
- The same number of terminals: two for a single element, three for a dual element.
- The same ceiling brackets or clips.
- 5
Install the new element
Connect the wires to the same terminals, slide the terminals through the wall and refit the screws and any ceiling clips.
- 6
Power on and test
Refit the racks, restore power and set broil. The element should glow evenly within a minute or two. If you moved the range, make sure the anti-tip bracket is engaged.
Buy the part
Get the right replacement
Buy the part
Broil element
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your range's model number. Shapes and lengths vary.
- The same number of terminals: two for a single element, three for a dual element.
- The same ceiling brackets or clips.
Know your limits
When to call a pro
Stop and call a pro if
- The wires behind the back wall are burned or too short to reach.
- The breaker trips after you install the new element.
- Broil still does nothing with a good element. The control may not be sending power.
FAQ
Broil element questions
Can I bake without a broil element?
Check your manual: many ovens bake with the bottom element. Replace it soon, and do not use the oven if the element is cracked or sparking.
Bake and broil both stopped at once. Is it both elements?
Unlikely. When both quit together, check the breaker first: an electric range needs both halves of its 240 V supply. Then look at the control board.
What does a dual broil element do?
It has two separate sections so the oven can heat the whole width or just the center. Each section is tested separately.
Related
Keep going
- SymptomOven not heatingThe oven will not heat, or barely warms. On an electric range the bake element is the usual cause, after the breaker. On a gas range a weak igniter is the most likely, after the gas supply. The sensor and the control come later.Open guide
- SymptomOven temperature wrongFood burns, stays raw or browns unevenly. Measure the real temperature first. A small, steady offset is often fixed in the settings. A big swing usually means a temperature sensor, an element or igniter that is failing, or a door that does not seal.Open guide
- Range partBake elementElectric ranges only. The bake element is the heating loop along the bottom of the oven. When it burns out, the oven heats slowly, unevenly or not at all on bake. It is usually two screws and two wires.Open guide
- Range partOven control boardThe control board is the electronic control behind the keypad and display. It reads the temperature sensor and switches the bake and broil elements or the gas igniters. When it fails, the display goes dead or garbled, keys stop responding, or the oven will not heat even with good parts.Open guide
- Range partOven temperature sensorThe temperature sensor is the thin probe on the oven's back wall. It tells the control how hot the oven is. When it drifts or fails, the oven runs too hot or too cool, or the control shows an error and stops heating.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
