WhatsBusted
3D model of a tankless burner and gas valve
Call a proAlso called tankless burner, tankless gas valve

Tankless burner and gas valve: signs of trouble and when to call a pro

The gas valve and burner are what turn gas into hot water. When they misbehave, the fix means gas fittings, gas pressure gauges and a sealed burner. This one is always a pro's job.

Who fixes it
A licensed pro
Typical pro cost
$150–$800
Gas valve jobs sit at the low end, burner work at the high end. Varies by unit and region

Gas work. It means shutting off and opening gas connections, setting burner gas pressure with a gauge, and resealing the burner area, then leak testing. Qualified pros only.

What it does

What the burner and gas valve does

Tankless gas water heaters only. When you open a hot tap, the control board opens the gas valve and the burner lights. The flame heats the heat exchanger, and the water picks up that heat as it flows through.

The gas valve does more than switch gas on and off. It controls how much gas reaches the burner, and the burner gas pressure is set for your gas type and altitude by a technician with a gauge.

Natural gas and propane units are set up differently. The gas type is on the unit's rating label, and a unit set for one gas must not run on the other.

Why it fails

Gas supply problems often look like burner trouble. Too little gas, an empty propane tank or a supply line problem causes ignition and flame failure codes.

Burners need periodic cleaning. Makers publish burner cleaning instructions for their technicians.

Gas valves wear out like other controls. A failed valve is usually replaced rather than repaired.

Symptoms

Signs the burner and gas valve is failing

  • Ignition or flame codes with the gas on

    The gas supply is on, the propane tank is not empty, and the unit still will not light or will not stay lit. A pro checks the gas pressure and the valve.

    Full diagnosis
  • Soot or a yellow flame

    Soot around the unit or the vent, or a lazy yellow flame through the sight glass, means the gas is not burning cleanly. That can make carbon monoxide. Turn the unit off and call a pro.

  • Gas smell near the unit

    A rotten-egg smell near the heater can mean a leak. Do not look for it. Leave the house and call your gas utility from outside.

    Full diagnosis

Safety first

Stay safe until it is fixed

  1. 1

    Smell gas? Leave first

    Do not light anything, touch electrical switches or use a phone inside. Leave the house right away and call your gas utility from outside or a neighbor's phone.

  2. 2

    CO alarm going off? Get out

    Get everyone, pets included, outside into fresh air and call 911. Do not go back in until emergency responders say it is safe.

  3. 3

    Turn it off and leave the cover on

    If you suspect the burner or gas valve, turn the unit off at its controller or power supply and call for service. Do not open the cover, adjust anything or touch the gas connections.

What a pro does

What to expect from the service call

  • Rule out the simpler causes first: the gas supply, the venting and air intake, and the igniter and flame rod.
  • Measure the gas pressure coming into the unit and at the burner with a gauge, and compare it with the maker's chart for the gas type and altitude.
  • Clean the burner per the maker's service instructions, or replace the burner or gas valve with the parts listed for the unit.
  • Reseal the burner area with new gaskets, check every gas connection for leaks, and set the burner pressure.
  • Test fire the unit and check for a clean flame, good venting and hot water at the set temperature.

Know your limits

When to call a pro

Stop and call a pro if

  • You smell gas at any point. Leave the house and call your gas utility from outside.
  • Ignition or flame codes keep coming back with the gas supply confirmed on.
  • You see soot or a yellow flame around the unit.
  • Your carbon monoxide alarm goes off near the water heater.
  • Anyone suggests adjusting the gas pressure or converting the unit to a different gas without the maker's parts and instructions.

FAQ

Tankless burner and gas valve questions

Can I replace the gas valve on my tankless water heater?

No. It means opening gas connections, setting the burner gas pressure with a gauge to the maker's chart and leak testing everything. Makers write this work for qualified technicians.

Can I clean the burner myself?

No. The burner sits in the sealed combustion area. Makers give burner cleaning instructions to their technicians, and the seals have to be put back right to keep exhaust inside.

My unit runs on propane and keeps showing an ignition code. What can I check?

Check that the propane tank is not empty and that its valve is open. If the tank is fine and the code comes back after one reset, call a pro.

How much does a tankless gas valve or burner repair cost?

Typically about $150 to $550 for a gas valve and about $400 to $800 for burner work, with a pro, part included. Prices vary by unit and region.

Related

Keep going

Get the next fix before it breaks

A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.

We send it with Kit. Privacy