Laundry center dryer runs but won't heat
The drum turns, so the motor and the controls are working. The fault is in the heat path, and that path is the same short list as on a full-size electric dryer.
Check these first
Five-minute checks, no tools
Both halves of the breaker on
The dryer uses a double breaker. One half can trip while the other stays on. Switch it fully off, then fully back on. On a fuse box, check both fuses.
Lint screen clean
Pull the [lint screen](/dryer/lint-screen) and clear it. A clogged screen makes the dryer overheat and trip its safety parts.
Air coming out outside
Run the dryer and check the outside hood. Weak air or a flap that stays shut points to a blocked [exhaust vent](/dryer/exhaust-vent).
Unplug every cord before testing
Before you take off any panel, unplug the laundry center. If it has two cords, one for the dryer and one for the washer, unplug both.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Thermal fuse
A one-time safety fuse that blows when the dryer overheats. On many electric dryers a blown fuse stops the dryer running at all, on others just the heat. Find out why it blew before you replace it. See the thermal fuse guide.
- 2DIY fix
Heating element
The coil can break or burn through, and then it cannot heat at all. A continuity test with the laundry center unplugged tells you. See the heating element guide.
- 3DIY fix
One side of the breaker tripped
Half the double breaker is off, so the dryer gets enough power to tumble but not to heat. If it keeps tripping, or the outlet looks scorched, call an electrician. The dryer no-heat page explains the two halves.
- 4DIY fix
Cycling thermostat
It switches the heat on and off to hold the temperature. If it fails open, the heat never comes on. See the cycling thermostat guide.
- 5DIY fix
High-limit thermostat
A backup safety switch that cuts the heat if the dryer overheats. Restricted airflow is the usual reason it trips, so check the vent too. See the high-limit thermostat guide.
- 6DIY fix
Timer or control board
The timer or electronic control tells the heat when to come on. Rule out the fuse, the element and the thermostats first, since they cost less. See the timer and control board guide.
What's happening
What your laundry center is doing
The dryer half of an electric laundry center runs on a 240 V circuit, just like a full-size electric dryer. The motor needs only one side of that supply, but the heating element needs both. When one side of the double breaker trips, the drum keeps turning and the air stays cold.
Power to the element passes a chain of safety parts on the way: the thermal fuse, the high-limit thermostat and the cycling thermostat. If any one of them opens, the element gets nothing. These are the same parts as in a full-size dryer, so the dryer no-heat guide applies here too.
The link that breaks most often is the thermal fuse. It blows when the dryer gets too hot, and that usually means a clogged lint screen or vent. Clear the airflow first, or a new fuse blows too.
Before you test anything, unplug the laundry center. Some have one power cord, others have a 240 V cord for the dryer and a 120 V cord for the washer, so unplug every cord. Access panels differ from a full-size dryer, so follow your laundry center's service manual or tech sheet for which panel to remove.
Know your limits
When to call a pro
Stop and call a pro if
- The breaker trips again after you reset it, or the outlet or plug looks scorched. Call an electrician.
- A new thermal fuse blows again soon after you fit it, and the vent is clear.
- You cannot find the tech sheet or the service manual for your laundry center and are not sure which panel to remove.
- You smell burning or see smoke. Unplug the laundry center and do not use it until it has been checked.
FAQ
Common questions
Are laundry center dryer parts the same as full-size dryer parts?
The same kinds of parts, doing the same jobs: a thermal fuse, a heating element, a cycling and a high-limit thermostat, and a timer or control. The tests in the full-size guides work the same way. The part numbers and the panels you remove to reach them are specific to your laundry center, so match parts by its model number and follow its service manual or tech sheet.
Should I just replace the thermal fuse?
Test it first, and if it has blown, find out why. A fuse blows when the dryer overheats, usually from a clogged lint screen or vent. Clean the exhaust vent before you fit a new one, or it will blow again.
Never bypass the fuse or a thermostat to get heat. They are what stop an overheating dryer from catching fire.
The breaker looks on. Can it still be the problem?
Yes. One half of a double breaker can trip while the handle barely moves. Switch it fully off, then fully on. If the dryer still will not heat and you want the supply voltage checked, that is a job for an electrician.
Related
Keep going
- SymptomLaundry center dryer takes too long to dryLoads need two cycles, or come out damp. On a laundry center, as on any vented dryer, the usual cause is restricted airflow: a clogged lint screen, a blocked vent or a crushed duct. Load size matters too.Open guide
- SymptomLaundry center dryer runs but won't tumbleThe dryer on top starts and its motor runs, but the drum stays still. The usual cause is a broken drum belt, then the idler pulley that keeps it tight, then worn drum rollers or a weak motor.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy