Dryer overheating or smells like burning
Smoke or flames? Keep the dryer door shut, get everyone out, close the doors behind you and call 911 from outside. Only a burning smell? Stop the dryer and switch off its breaker, or unplug it if the plug is easy to reach. On a gas dryer, close the gas shutoff if you can reach it without pulling the dryer out. Once it has cooled, the cause is often lint, and you can usually clear that yourself.
Check these first
Five-minute checks, no tools
Smoke first, then the power
If there is smoke or flame, do not open the dryer door: get everyone out, close the doors and call 911. Otherwise switch off the dryer's breaker, or unplug it. If the plug, cord or outlet feels hot or looks scorched, do not touch it. Use the breaker. Pressing Stop, Pause or Power does not disconnect the dryer.
Gas dryer: close the gas shutoff
Only if there is no smoke and you can reach it without pulling the dryer out: turn the handle on the gas line a quarter turn, so it sits crosswise to the pipe. If you smell gas, skip this. Do not touch any switches. Leave the house and call your gas utility or 911 from outside.
Lint screen and its slot
Once the dryer is cool, pull the [lint screen](/dryer/lint-screen) and clear it. Look into the slot it slides into for lint packed below.
The duct behind the dryer
Look behind the dryer. The duct should be rigid or semi-rigid metal, as short and straight as it can be, and not crushed, kinked or packed with lint. Plastic or foil duct should be replaced.
The flap outside
Find the vent hood outside. The flap should swing freely and the opening should be free of lint, nests and snow. Lint around it can mean the [exhaust vent](/dryer/exhaust-vent) needs cleaning.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Lint-clogged exhaust vent
The most common cause. Lint in the duct or at the hood outside traps the heat. Clothes take longer to dry, the dryer and clothes feel very hot, and little air comes out outside.
Fix the exhaust vent30 min–1.5 hr$15–$30 - 2DIY fix
Clogged lint screen or screen slot
A full screen, or lint packed in the slot below it, chokes the airflow at the very start. Clear the screen every load.
Fix the lint screen5–20 min$20–$100 - 3DIY fix
Crushed, kinked or foil duct
The duct behind the dryer is squashed against the wall, or it is plastic or foil accordion duct that sags and fills with lint. Replace it with rigid or semi-rigid metal duct.
Fix the exhaust vent30 min–1.5 hr$15–$30 - 4DIY fix
Slipping or worn drum belt
A hot rubber smell, often with squealing. A worn belt slips on the motor pulley and heats up from the friction.
Fix the belt30 min–2 hr$10–$70 - 5DIY fix
Seized idler pulley
The pulley that keeps the belt tight stops spinning, so the belt drags across it. Burning rubber and a squeal from low in the cabinet. Replace the belt too if it is glazed.
Fix the idler30 min–1.5 hr$8–$30 - 6Call a pro
Lint built up inside the cabinet
Lint that gets past the screen collects inside the cabinet, around the heater or burner. It can scorch and smell, and with poor airflow, or a safety part bypassed, it can catch fire. Have a service tech clean inside the cabinet from time to time. Some makers say about once a year.
- 7DIY fix
Cycling thermostat stuck closed
Every heat setting runs hot even with a clean vent, and thermal fuses keep blowing. The thermostat never opens to rest the heat.
Fix the cycling thermostat20–45 min$5–$60 - 8DIY fix
Heating element shorted to its housing
Electric dryers only. A sagging coil touches the metal housing and can keep heating even when the controls switch the heat off. The dryer still blows hot air on air-only.
Fix the element45 min–2 hr$30–$90 - 9DIY fix
Worn drum bearing, rollers or glides
The drum drags on worn supports. A worn bearing or glides can smell like hot metal or plastic, usually with thumping or scraping.
Fix the rollers45 min–3 hr$15–$60 - 10DIY fix
Drive motor overheating
A hot electrical or rubbery smell from low in the cabinet, often after a big, heavy load or when something makes the drum drag. The motor's built-in protector may stop it until it cools.
Fix the motor1 hr–3 hr$60–$200 - 11Call a pro
Burned power cord connection
Electric dryers. A sharp electrical smell or scorch marks at the back where the cord connects. A loose wire there can overheat and melt the terminal block. Leave it off at the breaker and have it repaired.
- 12DIY fix
Control board relay stuck on
Electronic models. The heat keeps running on air-only even though the heating element tests fine, because a relay on the board will not let go.
Fix the timer / board15 min–2 hr$50–$300
What's happening
What your dryer is doing
A dryer has to push its hot, damp air out through the vent. When lint packs the screen, the duct or the hood outside, the heat stays inside the cabinet. Lint is one of the things that most often catches fire first in dryer fires, and failing to clean it out is the leading cause of them. So treat a hot, burning smell as a warning, not a nuisance.
Plastic or foil accordion duct makes this worse. It traps lint and crushes or kinks easily behind the dryer. Dryer makers call for metal duct instead.
A hot rubber smell often comes from the drive belt. It slips when it is worn, or when the idler pulley seizes and the belt drags across it. You often hear squealing too. A worn drum bearing or worn glides can give a hot metal or plastic smell, often with scraping.
If the airflow is fine and the dryer still runs too hot, look at the heat circuit. A cycling thermostat stuck closed makes every heat setting run hot. If the dryer still blows hot air on an air-only setting, the heat is not switching off at all. On an electric dryer that usually means a heating element touching its housing. On some electronic models, a stuck relay on the control board does the same.
A sharp electrical smell from the back of an electric dryer can come from the power cord connection. A loose wire there can heat up and melt the terminal block it screws onto.
Some causes are in the load itself. Bath mats and other items with foam, rubber or plastic backing can scorch in the heat, so line dry them. An overpacked drum also slows the airflow and runs hotter.
A brand-new dryer can smell hot or oily the first few times it runs, as factory oils and new parts warm up. Running it empty for about 15 minutes helps. Too much detergent left in the clothes can also smell scorched.
Know your limits
When to call a pro
Stop and call a pro if
- You see smoke or flames. Keep the dryer door shut, get everyone out, close the doors behind you and call 911 from outside.
- You smell gas near a gas dryer. Do not touch any switches or the plug. Leave the house and call your gas utility or 911 from outside.
- A carbon monoxide alarm goes off. Get everyone outside to fresh air and call 911 or the fire department from outside.
- You find scorch marks, melted plastic or burned wires at the power cord connection or anywhere in the wiring.
- The vent is clean but lint has built up inside the cabinet, around the heater or burner. Have a service tech clean it out.
- It still runs too hot after you clean the screen, the duct and the vent, or new thermal fuses keep blowing.
- The burning smell is near the burner or gas valve on a gas dryer.
- A burning smell keeps coming back on a dryer that is not new.
- The vent runs to the roof, is very long, or you cannot reach the outside hood safely.
FAQ
Common questions
Is it safe to keep using a dryer that smells like burning?
No. Stop, cut the power and find the cause first. The conditions that make the smell, lint near heat or parts rubbing, are the same ones that start dryer fires. Never bypass the thermal fuse or a thermostat to keep it running, and do not run a dryer while you are out or asleep.
My dryer is brand new. Is a burning smell normal?
Often, yes, for the first few uses. Makers say a mild hot or oily smell is normal at first. Run it empty for about 15 minutes with the room aired out. If you see smoke, or the smell gets stronger or does not fade, stop and contact the maker or installer.
Why does my dryer smell like burning rubber?
Usually the belt is slipping. A worn drum belt slips on its own, and a seized idler pulley makes the belt drag across it. Unplug the dryer, and on a gas dryer close the gas shutoff. Then open it and spin the idler by hand. Replace whichever part is worn, and the belt too if it is shiny or cracked.
Can clothes catch fire after the dryer stops?
Yes. Clothes with oil on them are the main risk, such as cooking oil, wood stain or finishing oils. Oily fabric can heat up on its own after drying. Do not dry anything that has had oil, gasoline or solvents on it, even after washing. Line dry it instead. Let the cool-down part of the cycle finish. If you stop early, take the load out and spread it out. Never leave a hot load piled in the dryer or a basket.
How often should I clean the dryer vent?
Clear the lint screen every load. Clean the vent duct at least once a year, and sooner if drying starts taking longer. Have the inside of the cabinet cleaned by a service tech from time to time. Some makers suggest once a year. Our exhaust vent guide walks you through the duct.
Related
Keep going
- SymptomDryer takes too long to dryLoads need two cycles, or come out damp. On gas and electric dryers alike, the usual cause is restricted airflow: a clogged lint screen, a blocked vent or a crushed duct. Load size matters too.Open guide
- SymptomDryer shuts off earlyThe cycle ends, or the dryer stops mid-cycle, and the clothes are still damp. On gas and electric dryers, the usual causes are a blocked vent making it overheat, a coated moisture sensor, or a door that will not stay shut.Open guide
- SymptomDryer squealing, squeaking or thumpingA squeal or squeak usually comes from the idler pulley or a motor bearing. A rhythmic thump usually comes from worn drum rollers, drum glides or a damaged belt. A rattle or knock can be the blower wheel.Open guide
- SymptomDryer runs but won't heatThe drum tumbles but the air stays cold. On an electric dryer, start with the breaker and the thermal fuse. On a gas dryer, start with the gas shutoff and watch the igniter.Open guide
- Dryer partExhaust vent and ductThe exhaust duct carries hot, damp air and lint from the back of the dryer to a hood outside. When lint packs into it, drying slows and the dryer runs hot. Gas and electric dryers both need it cleaned about once a year.Open guide
- Dryer partLint screenThe lint screen catches fluff before it reaches the vent. A clogged or coated screen slows drying and makes the dryer run hot. Gas and electric dryers both have one, and cleaning it takes a minute.Open guide
- Dryer partDrum beltThe drum belt wraps around the drum and the motor pulley and turns the drum. When it breaks, the drum stops tumbling. Gas and electric dryers both have one, and the swap is the same on both.Open guide
- Dryer partIdler pulleyThe idler pulley is a small spring-loaded wheel that keeps the drum belt tight. When its bearing wears, it squeals. Gas and electric dryers both have one.Open guide
- Dryer partCycling thermostatThe cycling thermostat switches the heat on and off to hold the drying temperature. Gas and electric dryers both use one. When it fails, the dryer gets no heat or runs too hot.Open guide
- Dryer partHeating elementElectric dryers only. The heating element is a coil of resistance wire that heats the air on its way into the drum. A broken coil means no heat. A quick ohm test confirms it.Open guide
- Dryer partThermal fuseThe thermal fuse is a one-time safety fuse that blows when the dryer overheats. Gas and electric dryers both have one. A blown fuse is a warning about airflow, so clean the vent before you replace it.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
